Paper Drying Rack - Laser Cut - Modular Design
A modular print hanging rack to hold your prints secure while the ink dries. Each rack is laser cut from 1/4" Baltic Birch plywood and uses a sliding marble to secure 5 prints per rack module.
****NOTE****
THIS IS A PRE-ORDER. Orders will be produced and shipped by FEB 20, 2024. US shipping is included in the price.
-Assembly-
Each rack comes FULLY ASSEMBLED with the marbles installed. The rack is modular and allows you to add on as many additional 5-print sections as you would like. You simply slide the end cap off, and slide on an additional section.
-Mounting-
There are two mounting options.
A) 5 mounting holes on top to hang the rack by a cord from your ceiling or shelf.
B) There are 5 vertical holes to screw the rack directly to your preferred location. You will need 1.25"+ long screws (not included).
-Order Options-
A) Single module rack with end caps. Holds 5 prints.
B) Two module rack with end caps. Holds 10 prints.
C) Three Module Rack with end caps. Holds 15 prints.
D) Single module section with no end caps. Hold 5 prints, used to extend an existing rack.
****Please contact me if you have a specific question or configuration, or even a customization and we can work together to create what you want.
ATTENTION: The modular racks contain glass marbles, and the laser-cut wood can have sharp corners. These are not for children and should be kept away from them.
The marbles gently pinch the paper against the wood panel of the rack to hold your prints. If pulled excessively, it can leave an impression on the paper. It takes very little effort for it to securely hold prints.
This rack IS NOT meant for wet paper. The marble will likely dent the paper, and the water could damage the plywood.
Please contact me with any questions and I'd be happy to answer.
A modular print hanging rack to hold your prints secure while the ink dries. Each rack is laser cut from 1/4" Baltic Birch plywood and uses a sliding marble to secure 5 prints per rack module.
****NOTE****
THIS IS A PRE-ORDER. Orders will be produced and shipped by FEB 20, 2024. US shipping is included in the price.
-Assembly-
Each rack comes FULLY ASSEMBLED with the marbles installed. The rack is modular and allows you to add on as many additional 5-print sections as you would like. You simply slide the end cap off, and slide on an additional section.
-Mounting-
There are two mounting options.
A) 5 mounting holes on top to hang the rack by a cord from your ceiling or shelf.
B) There are 5 vertical holes to screw the rack directly to your preferred location. You will need 1.25"+ long screws (not included).
-Order Options-
A) Single module rack with end caps. Holds 5 prints.
B) Two module rack with end caps. Holds 10 prints.
C) Three Module Rack with end caps. Holds 15 prints.
D) Single module section with no end caps. Hold 5 prints, used to extend an existing rack.
****Please contact me if you have a specific question or configuration, or even a customization and we can work together to create what you want.
ATTENTION: The modular racks contain glass marbles, and the laser-cut wood can have sharp corners. These are not for children and should be kept away from them.
The marbles gently pinch the paper against the wood panel of the rack to hold your prints. If pulled excessively, it can leave an impression on the paper. It takes very little effort for it to securely hold prints.
This rack IS NOT meant for wet paper. The marble will likely dent the paper, and the water could damage the plywood.
Please contact me with any questions and I'd be happy to answer.
A modular print hanging rack to hold your prints secure while the ink dries. Each rack is laser cut from 1/4" Baltic Birch plywood and uses a sliding marble to secure 5 prints per rack module.
****NOTE****
THIS IS A PRE-ORDER. Orders will be produced and shipped by FEB 20, 2024. US shipping is included in the price.
-Assembly-
Each rack comes FULLY ASSEMBLED with the marbles installed. The rack is modular and allows you to add on as many additional 5-print sections as you would like. You simply slide the end cap off, and slide on an additional section.
-Mounting-
There are two mounting options.
A) 5 mounting holes on top to hang the rack by a cord from your ceiling or shelf.
B) There are 5 vertical holes to screw the rack directly to your preferred location. You will need 1.25"+ long screws (not included).
-Order Options-
A) Single module rack with end caps. Holds 5 prints.
B) Two module rack with end caps. Holds 10 prints.
C) Three Module Rack with end caps. Holds 15 prints.
D) Single module section with no end caps. Hold 5 prints, used to extend an existing rack.
****Please contact me if you have a specific question or configuration, or even a customization and we can work together to create what you want.
ATTENTION: The modular racks contain glass marbles, and the laser-cut wood can have sharp corners. These are not for children and should be kept away from them.
The marbles gently pinch the paper against the wood panel of the rack to hold your prints. If pulled excessively, it can leave an impression on the paper. It takes very little effort for it to securely hold prints.
This rack IS NOT meant for wet paper. The marble will likely dent the paper, and the water could damage the plywood.
Please contact me with any questions and I'd be happy to answer.